The patch #102460 already implements separate DT/LI/SE for parallel sub
function. Crashes have been reported while region generator tries using
oringinal function's DT while creating new parallel sub function due to
checks in #101198. This patch aims at fixing those cases by switching
the DT/LI while generating parallel function using Region Generator.
Fixes#117877
The patch sets the vectorization metadata to false for Polly's fallback
loops. These are the loops executed when RTCs fail. This minimizes the
multiple loop versioning carried out by Polly and subsequently by the
Loop Vectorizer.
---------
Co-authored-by: Michael Kruse <github@meinersbur.de>
Rename the function to reflect its correct behavior and to be consistent
with `Module::getOrInsertFunction`. This is also in preparation of
adding a new `Intrinsic::getDeclaration` that will have behavior similar
to `Module::getFunction` (i.e, just lookup, no creation).
As specified in the docs,
1) raw_string_ostream is always unbuffered and
2) the underlying buffer may be used directly
( 65b13610a5 for further reference )
* Don't call raw_string_ostream::flush(), which is essentially a no-op.
* Avoid unneeded calls to raw_string_ostream::str(), to avoid excess indirection.
DominatorTree, LoopInfo, and ScalarEvolution are function-level analyses
that expect to be called only on instructions and basic blocks of the
function they were original created for. When Polly outlined a parallel
loop body into a separate function, it reused the same analyses seemed
to work until new checks to be added in #101198.
This patch creates new analyses for the subfunctions. GenDT, GenLI, and
GenSE now refer to the analyses of the current region of code. Outside
of an outlined function, they refer to the same analysis as used for the
SCoP, but are substituted within an outlined function.
Additionally to the cross-function queries of DT/LI/SE, we must not
create SCEVs that refer to a mix of expressions for old and generated
values. Currently, SCEVs themselves do not "remember" which
ScalarEvolution analysis they were created for, but mixing them is just
as unexpected as using DT/LI across function boundaries. Hence
`SCEVLoopAddRecRewriter` was combined into `ScopExpander`.
`SCEVLoopAddRecRewriter` only replaced induction variables but left
SCEVUnknowns to reference the old function. `SCEVParameterRewriter`
would have done so but its job was effectively superseded by
`ScopExpander`, and now also `SCEVLoopAddRecRewriter`. Some issues
persist put marked with a FIXME in the code. Changing them would
possibly cause this patch to be not NFC anymore.
Uses the new InsertPosition class (added in #94226) to simplify some of
the IRBuilder interface, and removes the need to pass a BasicBlock
alongside a BasicBlock::iterator, using the fact that we can now get the
parent basic block from the iterator even if it points to the sentinel.
This patch removes the BasicBlock argument from each constructor or call
to setInsertPoint.
This has no functional effect, but later on as we look to remove the
`Instruction *InsertBefore` argument from instruction-creation
(discussed
[here](https://discourse.llvm.org/t/psa-instruction-constructors-changing-to-iterator-only-insertion/77845)),
this will simplify the process by allowing us to deprecate the
InsertPosition constructor directly and catch all the cases where we use
instructions rather than iterators.
This flag enable the user to print debug Info from all the passes and
helpers inside polly at once. This will help a novice user as well to
work in polly without explicitly having to know which parts of polly has
actually kicked in and pass them via -debug-only.
These are the last remaining "trivial" changes to passes that use
Instruction pointers for insertion. All of this should be NFC, it's just
changing the spelling of how we identify a position.
In one or two locations, I'm also switching uses of getNextNode etc to
using std::next with iterators. This too should be NFC.
---------
Merged by: Stephen Tozer <stephen.tozer@sony.com>
It's becoming potentially unsafe to insert a PHI instruction using a plain
Instruction pointer. Switch all the remaining sites that create and insert
PHIs to use iterators instead. For example, the code in
ComplexDeinterleavingPass.cpp is definitely at-risk of mixing PHIs and
debug-info.
This removes `CreateMalloc` from `CallInst` and adds it to the `IRBuilderBase`
class.
We no longer needed the `Instruction *InsertBefore` and
`BasicBlock *InsertAtEnd` arguments of the `createMalloc` helper
function because we're using `IRBuilder` now. That's why I we also don't
need 4 `CreateMalloc` functions, but only two.
Differential Revision: https://reviews.llvm.org/D158861
The method is marked for deprecation. Delete the method and move all of
its consumers to use the DomTreeUpdater version.
Reviewed By: foad
Differential Revision: https://reviews.llvm.org/D149428
Polly-ACC is unmaintained and since it has never been ported to the NPM pipeline, since D136621 it is not even accessible anymore without manually specifying the passes on the `opt` command line.
Since there is no plan to put it to a maintainable state, remove it from Polly.
Reviewed By: grosser
Differential Revision: https://reviews.llvm.org/D142580
Polly's internal vectorizer is not well maintained and is known to not work in some cases such as region ScopStmts. Unlike LLVM's LoopVectorize pass it also does not have a target-dependent cost heuristics, and we recommend using LoopVectorize instead of -polly-vectorizer=polly.
In the future we hope that Polly can collaborate better with LoopVectorize, like Polly marking a loop is safe to vectorize with a specific simd width, instead of replicating its functionality.
Reviewed By: grosser
Differential Revision: https://reviews.llvm.org/D142640
I went over the output of the following mess of a command:
`(ulimit -m 2000000; ulimit -v 2000000; git ls-files -z | parallel --xargs -0 cat | aspell list --mode=none --ignore-case | grep -E '^[A-Za-z][a-z]*$' | sort | uniq -c | sort -n | grep -vE '.{25}' | aspell pipe -W3 | grep : | cut -d' ' -f2 | less)`
and proceeded to spend a few days looking at it to find probable typos
and fixed a few hundred of them in all of the llvm project (note, the
ones I found are not anywhere near all of them, but it seems like a
good start).
Reviewed By: inclyc
Differential Revision: https://reviews.llvm.org/D131167
The IR Verifier requires that every call instruction to an inlineable
function (among other things, its implementation must be visible in the
translation unit) must also have !dbg metadata attached to it. When
parallelizing, Polly emits calls to OpenMP runtime function out of thin
air, or at least not directly derived from a bounded list of previous
instruction. While we could search for instructions in the SCoP that has
some debug info attached to it, there is no guarantee that we find any.
Our solution is to generate a new DILocation that points to line 0 to
represent optimized code.
The OpenMP function implementation is usually not available in the
user's translation unit, but can become visible in an LTO build. For
the bug to appear, libomp must also be built with debug symbols.
IMHO, the IR verifier rule is too strict. Runtime functions can
also be inserted by other optimization passes, such as
LoopIdiomRecognize. When inserting a call to e.g. memset, it uses the
DebugLoc from a StoreInst from the unoptimized code. It is not
required to have !dbg metadata attached either.
Fixes#56692
Most clients only used these methods because they wanted to be able to
extend or truncate to the same bit width (which is a no-op). Now that
the standard zext, sext and trunc allow this, there is no reason to use
the OrSelf versions.
The OrSelf versions additionally have the strange behaviour of allowing
extending to a *smaller* width, or truncating to a *larger* width, which
are also treated as no-ops. A small amount of client code relied on this
(ConstantRange::castOp and MicrosoftCXXNameMangler::mangleNumber) and
needed rewriting.
Differential Revision: https://reviews.llvm.org/D125557
This make is obivious that a class was not intended to be derived from.
NPM analysis pass can unfortunately not marked as final because they are
derived from a llvm::Checker<T> template internally by the NPM.
Also normalize the use of classes/structs
* NPM passes are structs
* Legacy passes are classes
* structs that have methods and are not a visitor pattern are classes
* structs have public inheritance by default, remove "public" keyword
* Use typedef'ed type instead of inline forward declaration
The legacy LoopUnswitch pass is only used in the legacy pass manager
pipeline, which is deprecated.
The NewPM replacement is SimpleLoopUnswitch and I think it is time to
remove the legacy LoopUnswitch code.
Fixes#31000.
Reviewed By: aeubanks, Meinersbur, asbirlea
Differential Revision: https://reviews.llvm.org/D124376
The `opt -analyze` option only works with the legacy pass manager and might be removed in the future, as explained in llvm.org/PR53733. This patch introduced -polly-print-* passes that print what the pass would print with the `-analyze` option and replaces all uses of `-analyze` in the regression tests.
There are two exceptions: `CodeGen\single_loop_param_less_equal.ll` and `CodeGen\loop_with_condition_nested.ll` use `-analyze on the `-loops` pass which is not part of Polly.
Reviewed By: aeubanks
Differential Revision: https://reviews.llvm.org/D120782
Ensure that function definitions match their declrations in header
files, even if they have no effect on linking. This includes
1. Both have the same __isl_* annotations
2. Both use the same type alias
3. Remove unused declarations that have no definition
4. Use explicit polly namespace qualifier for definitions; generally,
the .cpp file should use at most an anon namespace region since
only symbols declared in the header file can be accessed from other
translation units anyway. For defintions that have been declared in
the header file, the explicit namespace qualifier ensures that both
match.
